How To Make A Dartboard Wall Protector? – Step by Step

You just got a new dartboard and you’re super excited to start playing, but then you realize that your walls are not protected.

If you don’t want to end up with holes in your wall, you need to buy a dartboard wall protector.

But before you do that, why not try making one yourself? It’s easy and only takes a few materials that you probably have lying around your house. But the question is how to make a dartboard wall protector.

To make a dartboard wall protector, first, find a piece of plywood or MDF that’s big enough to cover the area around your dartboard. Then, cut out a circular hole in the center of the plywood or MDF using a jigsaw. Once you’ve done that, you can paint it. Finally, attach the plywood or MDF to the wall using screws or nails.

Keep reading to find out more because in this article I’ll show you a step-by-step guide.

How To Make A Dartboard Wall Protector

After doing some research I found the top 5 steps to make your dartboard wall protector!

1. Hang The Board On The Wall

The first step is to find a wall on which you want to hang your dartboard on. Then, using a level, mark where the center of the bullseye will be. Next, using a stud finder, locate the studs in the wall and mark them.

Once you have found the studs, use a drill to make pilot holes for the screws. Now it’s time to hang the dartboard! Place the screws into the pilot holes and screw them into the studs.

Be careful not to over-tighten the screws, as this could damage the wall or pull the dartboard out of alignment.

2. Measure And Cut Your Plywood

The next step is to measure and cut your plywood. You’ll want to use a straight edge and a saw to make sure your cuts are clean and precise.

The size of the plywood will depend on the size of your dartboard and the space you have available. Once you’ve cut the plywood, sand the edges to smooth them out.

3. Attach The Plywood To The Wall

Now it’s time to attach the plywood to the wall. You can do this by screwing it into the studs or by using heavy-duty adhesive. If you’re using screws, be sure not to over-tighten them as this could damage the plywood or pull it out of alignment.

If you’re using adhesive, be sure to apply it evenly and allow it to dry completely before attaching the plywood to the wall.

4. Hang Your Dartboard

Now that the plywood is in place, you can hang your dartboard! Simply position the dartboard on the plywood and use screws or adhesive to attach it in place.

Be sure not to over tighten the screws or apply too much adhesive, as this could damage the dartboard or pull it out of alignment.

5. Add Your Bullseye

The final step is to add your bullseye! You can use a store-bought bullseye or make your own using a piece of cardboard or paper. Once you have your bullseye, position it in the center of the dartboard and use adhesive to attach it in place.

Allow the adhesive to dry completely before hanging your dartboard up and enjoying a game!

That’s it! You now have a homemade dartboard wall protector that will help extend the life of your dartboard and keep your walls looking great.

Things To Keep In Mind When Hanging Your Dartboard Wall Protector:

If you are going to be using your dartboard wall protector in a professional setting or a tournament, then there are a few things that you need to keep in mind.

Make sure that the wall protector is hung at the correct height. The standard height for a dartboard is 5 feet 8 inches from the ground to the center of the bullseye.

If you are hanging your dartboard wall protector in a home setting, then you can hang it at whatever height is comfortable for you and your family. Just make sure that everyone who is going to be playing darts can reach the dartboard easily.

Another thing to keep in mind is the distance from the wall to the dartboard. The standard distance for a dartboard is 7 feet 9 inches from the front of the board to the back of the board.

This gives you plenty of room to throw your darts without worrying about hitting the wall. If you are hanging your dartboard in a home setting, you can adjust the distance from the wall to the dartboard to make it more challenging or easier for the people who are playing.

Once you have hung your dartboard wall protector, make sure that you test it out to make sure that it is working properly. Hang some targets on the wall and see how well they stay in place.

If you find that the targets are not staying in place, then you may need to adjust the way that you are hanging the dartboard wall protector. Make sure that you follow all of the instructions that came with your dartboard wall protector so that you can get the best results.

Hanging a dartboard wall protector is a great way to protect your walls from darts. By following these simple tips, you can make sure that your dartboard wall protector is hung correctly and that it will last for a long time.


So, there you have it. Your very own dartboard wall protector. It’s easy to make and will help keep your walls safe from darts (and save you some money in the process). If you give this project a try, be sure to let us know how it turns out!

I hope you like this step-by-step guide on how to make a dartboard wall protector.


If you’ve still got questions about how to make a dartboard wall protector, then these may help:

What goes behind a dart board?

There are a few things that you can use to protect your wall behind a dartboard. The most common and popular option is to use a dartboard backboard. This is a piece of material, usually plywood or fiberboard, that you hang on the wall behind your dartboard. Backboards help to protect your wall from stray darts, and they can also add a bit of style to your game room.

Another option for protecting your wall is to use a dartboard cabinet. Cabinets are larger than backboards, and they typically have doors that close to enclose the dartboard when it’s not in use. This offers the best protection for your wall, but cabinets can be more expensive than backboards.

You can also make your wall protector by covering a piece of plywood or fiberboard with foam padding and then wrapping it in fabric. This DIY option will still provide some protection for your wall, and you can customize the fabric to match your game room’s décor. Follow the above steps!

How do you cover a dart hole in the wall?

If you find a stray dart has made a hole in your wall, you can easily cover it with a piece of putty or spackle. Just fill in the hole and then repaint the area to match the rest of your wall. You can also use this method to cover any small nicks or scratches in your paint.

Note: We are partner of amazon affiliates programme, Article may contain affiliates links We may earn from qualifying purchase at no additional cost to you.

Best Darts

Best Dartboard